Exactly How to Install a Bath Tub Yourself: Removing and Replacing.
Exactly How to Install a Bath Tub Yourself: Removing and Replacing.
Blog Article
Do you find yourself trying to find advice concerning A Step-by-Step Guide to Installing a Bathtub?
Setting up a bath tub isn't exactly rocket science, but it does need strong plumbing, woodworking, and also occasionally, tiling abilities. Replacing an old bathtub with a new one is also a moderately difficult project. If the old tub is readily available, the job can move speedily; if you have to open a wall to remove the old tub and place the brand-new bath tub, the job is a lot harder. In either instance, the task is within a residence handyman's abilities, although you will need a helper to move out the old tub as well as set in the new one. Make certain you have actually certified on your own for the work and also fit trying it. Rather than hiring a service provider to take control of a halfway-completed job, it is better to take into consideration using one before you begin. Opportunities are you might need a professional plumber to make tube links.
This short article will certainly aid you set up a brand-new tub in your restroom if you have already bought a brand-new bathtub and also do not require to alter the arrangement of your previous water pipes.
Your tools as well as material list must comprise the following:
Removing Old Taps
If you require to replace old faucets with new ones as a part of your installment, then the first thing you should do is detach the water supply. After doing so, activate the taps to drain pipes any water staying in the system. The procedure of eliminating the existing taps can be fairly troublesome due to the limited gain access to that is often the instance.
Utilize a container wrench (crowsfoot spanner) or a tap tool to reverse the nut that connects the supply pipelines to the taps. Have a towel ready for the remaining water that will originate from the pipes. As soon as the supply pipes have actually been removed, make use of the exact same device to loosen the nut that holds the faucets onto the bath/basin. You will require to stop the solitary taps from transforming during this process. Once the taps have actually been gotten rid of, the holes in the bath/basin will certainly have to be cleaned up of any kind of old securing substance.
Prior to moving on to fit the brand-new faucets, compare the pipe connections on the old faucets to the brand-new faucets. If the old taps are longer than the new faucets, then a shank adapter is needed for the brand-new faucets to fit.
Fitting New Taps
If the tails of the new faucets are plastic, then you will certainly need a plastic connector to avoid damages to the thread. One end of the adapter fits on the plastic tail of the faucet as well as the other end provides a link to the current supply pipes.
If you require to fit a monobloc, then you will call for decreasing couplers, which links the 10mm pipeline of the monobloc to the conventional 15mm supply pipeline.
Next, position the faucet in the mounting hole in the bath/basin making certain that the washers remain in area between the tap and also the sink. Secure the tap in place with the supplier provided backnut. When the faucet is firmly in place, the supply pipes can be connected to the tails of the taps. The faucets can either be attached by using corrugated copper piping or with typical faucet adapters. The former type ought to be attached to the faucet ends first, tightening only by hand. The supply pipes can later on be attached to the various other end. Tighten both ends with a spanner after both ends have been linked.
Setting up the Bath tub
Using the two wooden boards under its feet, put the tub in the called for placement. The wooden boards are useful in evenly spreading the weight of the tub over the location of the boards as opposed to concentrating all the weight onto 4 small points.
The next goal is to make sure that the tub is leveled all round. This can be achieved by inspecting the level and also readjusting the feet on the bathtub up until the spirit level reviews degree.
To install taps, fit the bottom of the furthest versatile faucet adapter to the ideal supply pipeline by making a compression sign up with; after that do the very same for the various other faucet.
Activate the water supply and check all joints and brand-new pipework for leakages and also tighten them if essential. Fill the tub as well as likewise examine the overflow electrical outlet and also the regular electrical outlet for leaks.
Finally, fix the bath paneling as described in the producer's instruction manual. Tiling as well as sealing around the bathtub should wait till the bath tub has actually been utilized a minimum of once as this will settle it right into its last setting.
Getting ready for the Setup
First of all, the sustaining framework provided with the bath ought to be fitted (if needed) according to the producer's instructions. Next, fit the taps or mixer to the bath tub. When suitable the faucet block, it is essential to make sure that if the tap comes with a plastic washing machine, it is fitted in between the bathroom as well as the taps. On a plastic bath, it is also reasonable to fit a sustaining plate under the faucets system to avoid strain on the bathtub.
Fit the flexible faucet adapters to the bottom of both taps using 2 nuts and olives (occasionally provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet opening, and after that pass the outlet through the hole in the bath. Use the nut provided by the supplier to fit the plug-hole. Take a look at the plug-hole outlet for an inlet on the side for the overflow pipe.
Next off, fit completion of the flexible overflow pipeline to the overflow electrical outlet. After that, screw the pipe to the overflow face which need to be fitted inside the bath. Ensure you make use of every one of the supplied washing machines.
Link the trap to the bottom of the waste electrical outlet on the tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the trap to the electrical outlet. Link the bottom of the overflow tube in a comparable manner.The bath should currently be ready to be suited its last setting.
Tiling Around the Bath tub
In the location where the bath fulfills the ceramic tile, it is necessary to secure the joins with a silicone rubber caulking. This is necessary as the fitting can relocate enough to split a rigid seal, creating the water to penetrate the wall surface between the bathroom as well as the tiling, leading to issues with dampness and also possible leakages to the ceiling below.
You can pick from a variety of coloured sealers to blend in your components and installations. They are sold in tubes as well as cartridges, and can securing spaces approximately a width of 3mm (1/8 inch). If you have a bigger gap to fill up, you can fill it with twists of drenched newspaper or soft rope. Bear in mind to always fill up the bathtub with water before securing, to allow for the motion experienced when the tub is in usage. The sealant can split rather early if you do not think about this movement before securing.
Alternatively, ceramic coving or quadrant ceramic tiles can be made use of to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and also cut to dimension, are additionally easily offered on the marketplace. It is advisable to fit the ceramic tiles making use of waterproof or waterproof sticky and also cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
As an avid reader on How to Install a Bathtub Yourself, I think sharing that editorial was a smart idea. Loved our review? Please share it. Help somebody else check it out. Thanks a lot for taking the time to read it.
Information Here Report this page